I am looking to create a program using the Adafuit Feather M4 Express, along with the Adafruit Prop Maker Board for the Feather. The specifics of the boards can be found below. Also the boards have the following components as part of them. This project is to be completed using the Arduino C/C++ Style language on the M4 board.
Adafruit Feather M4 Express:
[login to view URL]
Adafruit Feather Prop Maker Board:
[login to view URL]
Analog Audio output:
[login to view URL]
LIS3DH Triple-Axis Accelerometer:
[login to view URL]
Arduino Writing to Flash Memory:
[login to view URL]
FastLED Library (FastFire2012):
[login to view URL]
Adafruit NeoPixels Library:
[login to view URL]
All of this is possible using the Feather Prop Maker Board: The guide above provides the detailed information on the pin outs, you can also see some particulars to using the Arduino IDE with the feather hardware here: [login to view URL]
I am looking to create a project that outputs to the NeoPixels using the FastFire2012 library, as well as the Adafruit NeoPixels code I want it to have the following modes
1) Fire (Red, white, Yellow, Black, Orange) (FastFire2012 Pallet)
2) Energy (Green, White, Yellow, Black light orange) (FastFire2012 Pallet)
3) Water (Blue, White, Yellow, Green, Black) (FastFire2012 Pallet)
4) Rainbow cycle (Adafruit Neo Pixel Library)
For the functionality I would like a push button to be used to select the mode, by pressing down on a momentary button and holding it down for more than 3 seconds, you enter mode selection. You can then select one of the 4 modes above. The mode selection would then be written to the flash memory of the Feather M4 Board. Mode is exited by holding the button for 3 more seconds.
When you press the momentary button, you have an audio “Power-Up” sound, and the neo-pixels light up to the selected pattern. While the NEO Pixles are lit up, and there is limited to no motion it plays an “idle” sound on a loop (continuously). When you “swing” the prop weapon, it registers and plays a “Swing” sound. If a certain velocity is reached or using the tap feature of the LIS3DH you can register a “Hit” sound, and the NeoPixels light up a solid color such as all white, then return to the selected pattern. When you press the momentary button again there is a “Power-down” sound and the neo pixels turn off. Think of this a lot light a light saber from Star Wars.
When the sword is lit up I would like to make the LED in the button light up as well. This can be done with a simple setting of the LED button to high. I will detail this port/button below.
Buttons/Pin outputs for Feather M4 board:
Number of Neo Pixels: 60
Neo Pixel Pin: 5
Power Pin: 10 – Used to supply power for NeoPixels, needs to be set to High)
Button Pin: 9
Red LED Pin: 11 – Used for 3W LED’s On the Prop Maker Board
Green LED Pin: 12 - Used for 3W LED’s On the Prop Maker Board
Blue LED Pin 13- Used for 3W LED’s On the Prop Maker Board
LIS3DH Pins:
SCK: 25
MOSI: 24
MISO: 23
CLK: 6
Sounds:
To be stored on the flash memory in a “Sounds” directory
[login to view URL]
[login to view URL]
[login to view URL]
[login to view URL]
[login to view URL]
Configuration:
To be stored on the flash memory in a file named “[login to view URL]”
I will help you and designing projects using Raspberry pi, Arduino, ESP8266, ESP32, Beaglebone, Linux & RTOS based target.
I can also teach you how to use these devices.
I can write, debug and extend your code!
Health monitoring sensors
All arduino & raspberry pi sheilds
Wireless Modules
WiFi (ESP8266 or any)
RF Modules (XBEE, NRF etc)
GSM & GPRS
Bluetooth
Accelerometer Gyro & IMU
Motors (DC Motor, Stepper Motor, Servo Motor & Brushless)
Buttons & Switches
Speakers and Buzzers
Rotatory Encoders
Humidity and Temperature
Flow
Smoke
Current and voltage
UV sensor
Communication Platforms & Protocols I have worked with include
HTTP
MQTT
SSL/TLS
Blynk
Thingspeak
Amazon IoT
NodeRed and many others
My research area is Embedded Systems, Power Electronics, AI and Robotics!
What else:
Extensive Comments in Code & Detailed Documentation
Free Circuit Diagrams, Schematics & Fritzing Diagram.
PCB of your Circuits & Projects
Free Project Revisions
Super Fast 2-3Hr Service
An easy project to be done, I m a solo developer,,,,u will get the best work accompanied with brotherhood,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,,
Hello
I'm an embedded software engineer and I would like to hear about your project requirements to estimate how much effort is needed to complete the job. so I can adjust my bid to job complexity.
Best regards
Hi,
We are a professional Manufacturing service that has extensive experience in CNC machining, 3D Printing, Injection Molding, Laser Cutting. We work with all materials and to all finishes including prototyping & end-product consumer retail goods working only the very best in industry standards to fit all budgets.
If you do not have the CAD file we can create them for you with our team of engineers & product designers and then get them to manufacturing.
Let me know if we can be of service; and please let me know if your interested in photos of our past work!
many thanks,
Conor
We are experts in bringing products to life! Please message me to see photos of our past work.