Simulation Jobs

I would like the IEEE 33-bus distribution feeder recreated in RSCAD v6 so that it runs smoothly in real time on my single-rack RTDS. The base network must be stable, clearly documented inside the workspace, and organised under three separate simulation cases: 1. Baseline (no DER, no EV) 2. PV + BESS + EVCS with V2G enabled 3. EVCS with V2G only I’ll provide the complete MATLAB data set that defines the component ratings, daily profiles, dispatch assumptions and any controller logic already worked out offline. Your task is to translate all of that into RSCAD, verify compile/run success at a 50 µs timestep, and deliver a balanced model that can be opened and executed immediately on the RTDS without further edits. Please let me know: • Your earliest start date and est...

Case study using open studio program to simulate a building and get energy and environment output and modifications

My 4.5 V circuit needs a small solar panel and the proper charge-management hardware so daylight tops the battery up automatically. I’m not sure what panel voltage or wattage is best, nor which controller IC will keep the Li-ion safe—so I need your electronics expertise. Scope of work – I'll share my schematic of the existing 4.5v circuit – Select or design a charge-controller stage that handles lithium-ion chemistry, prevents over-charge/over-discharge, and outputs a stable 4.5 V rail to the load. – Provide a clear schematic, concise BOM with part numbers that are easy to source, and wiring instructions I can follow on perfboard or a small PCB. – Advise on any protection components (diodes, fuses, reverse-polarity safeguards) so the device...

Project Description: I am looking for an experienced RF/Antenna Design freelancer to design and simulate a flexible wearable antenna using ANSYS HFSS for my final year project. Scope of Work: Design of a flexible microstrip/patch antenna for 5G (Sub-6 GHz, e.g., 3.3–3.8 GHz) and/or IoT band Selection and modeling of appropriate flexible substrate material (e.g., Polyimide, Rogers RT/duroid, textile substrate) Optimization of antenna parameters (length, width, feed position, ground structure, etc.) Simulation and analysis of key parameters: S11 (Return Loss ≤ -10 dB) VSWR Gain and Directivity Radiation Pattern (2D & 3D) Bandwidth Radiation Efficiency Bending analysis to evaluate performance under curvature (wearable condition) Parametric study and comparison with provided refe...

PROJECT OVERVIEW We are seeking an experienced Power Electronics / Control Systems Engineer to support a STATCOM upgrade project Upgrade from old controller PSR II ABB uses the ABB AC800PEC . The objective is to design, implement, and deploy control algorithms developed in Simulink / MATLAB into the AC800PEC Toolbox environment, ensuring real-time execution and stable grid performance. ________________________________________ SCOPE OF WORK The selected engineer will: 1 Control Algorithm Development • Develop and/or refine dq-axis current control • Design PLL (Phase-Locked Loop) for grid synchronization • Implement DC link voltage control • Reactive power / voltage regulation control • PWM generation strategy 2 Model-Based Design • Develop control models in Sim...

I have a gas-liquid separator whose internal geometry needs to be verified before fabrication. The task is a complete CFD study of multiphase flow through the vessel, capturing the interaction between gas and liquid phases. My main concerns are flow distribution across the internals, overall pressure drop, and the resulting phase-separation efficiency, so the model must resolve these three metrics quantitatively. A CAD file of the current layout, design operating conditions, and fluid properties will be supplied at project start. The simulation should be run at the specified throughput, using an appropriate multiphase model (VOF, Euler-Euler, or similar) in Fluent, CFX, OpenFOAM, or another recognised solver, with mesh independence demonstrated. Please include transient behaviour if it ma...

NVIDIA Omniverse Developer (USD, Python, Simulation) – Hourly Contract ⸻ Job Description We are looking for an experienced NVIDIA Omniverse developer to support our project on an hourly basis. The work involves building, modifying, and optimizing workflows within NVIDIA Omniverse, with a focus on USD pipelines, Python scripting, and simulation or visualization tasks. This is a technical role suited for someone who has hands-on experience with Omniverse rather than general 3D tools only. ⸻ Scope of Work Depending on expertise, tasks may include: • Working with USD (Universal Scene Description) assets and stage composition • Developing or modifying Python scripts inside Omniverse • Setting up or improving Omniverse extensions • Simulation, visualization, ...

I’m kicking off a multi-phase R&D effort devoted to the design and development of cutting-edge microstrip antennas. The overarching targets are straightforward: boost usable bandwidth while simultaneously lifting signal strength, all without compromising the core advantages of printed technology. Phase by phase, I’ll be iterating from theoretical models through to lab-verified prototypes. You’ll take the lead on concept generation, electromagnetic simulation (HFSS, CST or an equivalent full-wave solver), layout refinement, and hand-over for fabrication. Once hardware comes back, we’ll compare measured S-parameters and radiation patterns against the simulated baseline, fine-tune, and document lessons learned for the next spin. Key deliverables • Simulation...

I've already built some prototypes of a circuit capable of switching a single 230 V, 16–30 A line to 4, 8, or 12 outputs—without power loss—but none of them have reached the standards I expect. I have schematics, calculations, thermal measurements, and test logs: enough material to clarify every technical detail and speed up your work. I need a senior designer who can transform all this into a final solution, complete with ESP32 firmware, a multilayer PCB (4 or 6 layers, JLCPCB production - 3oz copper), and an accurate and documented simulation before production. Technical requirements to be met: • Maximum energy efficiency, component protection, and precision switching under load. • Integrated remote control, real-time monitoring, and an alarm system. &b...

I need solution for three questions electronics MATLAB/simulations file attached 1.35 1.36 1.39 Only induvial experts and tutors no agencies After this i will have so many projects Fair price flexible with time good availability of time

Want to add custom commands upload to robot and from retroit control execute that commands

I’ve drafted a single-layer board in Altium Designer and now need a seasoned set of eyes to run thorough simulations before I commit to building the first prototype. Your task is to import my project, verify the stack-up and component models, and perform all relevant electrical, thermal, and rule-check simulations available in Altium. Key goals • Confirm that signal integrity and power distribution meet design intent. • Flag any DRC or manufacturing issues early so I can correct them before fabrication. • Produce a concise simulation report summarizing the tests run, key plots or screenshots, and your recommendations. Deliverables 1. Updated Altium project files with all simulation settings preserved. 2. PDF or DOC report of findings and suggested fixes. ...

I'm looking for a detailed simulation of 5G soft handover in Matlab for research and analysis purposes. Key Requirements: -Simulate system-level handover with integrated PHY and MAC layer modeling in MATLAB -Consider satellite, aerial (e.g., UAV/HAPS), and terrestrial segments within a SAGIN scenario -Support evaluation of handover performance using KPIs such as handover latency, throughput, packet loss, and connection stability Provide comprehensive analysis and visualization of results (e.g., KPI trends, CDFs, outage/interruption time, HO failure rate) Ideal Skills and Experience: - Proficiency in Matlab - Strong understanding of 5G network architecture and handover mechanisms - Experience in network simulation and performance analysis - Ability to present data clearly and concis...

I need a compact, production-ready circuit that brings reliable wireless communication to a new consumer-electronics device. The work begins with schematic capture and component selection, moves through PCB layout, and finishes with ready-to-manufacture Gerbers, a complete BOM, and clear test guidelines. The radio link is the heart of the design, so careful RF layout, antenna matching, and regulatory-compliant power levels are essential. Bluetooth LE is my preferred protocol, though I am open to Wi-Fi or other 2.4 GHz solutions if you can demonstrate lower cost or better battery life without sacrificing performance. Please plan on: • Delivering editable design files in Altium, KiCad, or Eagle, plus PDFs for quick review • Calling out any critical components with long le...

I need a complete transient (surge) study for a 13-km buried pipeline that carries treated wastewater from our STP. The goal is to predict all critical pressure extremes, then turn those numbers into practical hardware locations so the line can be protected before we commission it. Scope of the study • Model the existing line geometry, elevations and flow data (I will forward the General Arrangement Drawing as soon as it is finalised). • Simulate the three key operating upsets that worry us: pump start/stop sequences, planned valve manoeuvres, and a full power-failure trip. • Identify positive and negative pressure envelopes, vapour pocket risks and column separation zones. • Translate the results into a clear markup on the GAD, showing where air-release/vacuum...

I’m building a desktop application in C# with WPF that will become the main human-machine interface for my CNC router. The immediate focus is a smooth, modern UI that drives fully automated routing operations and can later be wired to my Beckhoff controller. Scope of work • Create a WPF desktop application (targeting .NET 6 or later) with a clear, touch-friendly layout. • Implement workflow screens that guide the operator through job selection, automatic tool-change, start / pause / stop, and real-time progress feedback. • Architect the code so that all machine calls are abstracted behind a service layer; I will plug this layer into the Beckhoff PLC via ADS or another Beckhoff-compatible protocol after the UI is finished. • Include basic safety interlocks ...

I’m refining a cross-flow fan-wing UAV concept and need a complete picture of how it will behave in the air and how the structure will cope with the resulting loads. On the aerodynamic side, I want accurate lift and drag coefficients across the flight envelope, clear visualisation of flow patterns and vortex behaviour around the fan-augmented wing, and a detailed pressure distribution map that I can feed back into the structural model. CFD in ANSYS Fluent, OpenFOAM or an equivalent solver is fine as long as mesh independence is demonstrated and transitional flow around the fan is captured. For structural integrity, my main focus is the wing and fan structure plus the control surfaces and their attachments. I’d like an FEA model (Abaqus, ANSYS Mechanical, or similar) that impor...

I need a fully-developed Simio model that follows every one of the 2,750 plates from the moment they arrive by truck until the last unit is set down in the yard. There are 109 colours, exactly 25 plates per colour, and each colour must remain together in the same three-slot crane position. If a later plate of an already-started colour shows up, the Rubber-Tired Gantry (RTG) has to travel back to that original position before it can discharge the plate. Operational facts you must replicate • Trucks: 10 per calendar day, 12 plates each, arrivals spread randomly over 24 h. • RTG travel speed: 4 km/h. • Crane positions: three usable slots per stop. • Discharge time: 1.5 min per plate, continuous 24 / 7 operation. Scope of the model – High-detail, entity-...

I would like a full TFET study carried out in Cogenda Visual TCAD that covers both 2-D and 3-D device representations. My end goal is to arrive at a structure—and a small demonstration circuit—whose operating point clearly illustrates ultra-low power consumption. Here’s what I need from you: • Build the TFET geometry in the tool, choose appropriate materials and doping profiles, then sweep critical design parameters until the device meets a low-power operating target (sub-threshold swing and leakage will be the key figures I’ll look at). • Run complete electrical simulations in 2-D first, then extend the validated setup to 3-D so I can compare dimensional effects. • Supply all Cogenda project files, meshes, command scripts, and export any pl...

I need a detailed fatigue analysis for FRP composites under cantilever loading conditions. The main goal is to predict fatigue life and generate S-N curves. Key Requirements: - Analyze fatigue behavior under cantilever loading - Predict fatigue life - Develop S-N curves Ideal Skills: - Expertise in fatigue analysis - Experience with FRP composites - Proficient in mechanical loading simulations Please include relevant experience in your bids.

Projeto: Engenharia Reversa de Placa Eletrônica Legada Descrição do Projeto Busco profissional com experiência comprovada em eletrônica para realizar engenharia reversa completa de uma placa eletrônica legada, com o objetivo de: Reproduzir fielmente o funcionamento elétrico original Modernizar componentes obsoletos Gerar documentação técnica completa e atualizada Garantir compatibilidade mecânica, elétrica e funcional com o equipamento original O projeto seguirá um procedimento técnico estruturado já definido internamente Escopo do Trabalho O profissional deverá executar as seguintes etapas: 1. Análise e Correlação do Esquemático Verificaç&...