Controller circuit design jobs

Filter

My recent searches
Filter by:
Budget
to
to
to
Skills
Languages
    Job State
    11,260 controller circuit design jobs found, pricing in NZD

    It is designing a discrete common-source amplifier satisfying the required gain, input impedance, output impedance...designing a discrete common-source amplifier satisfying the required gain, input impedance, output impedance, and frequency response characteristics. Then you will simulate your circuit on LTSpice to verify the requirements are met.

    $58 (Avg Bid)
    $58 Avg Bid
    4 bids

    Hi, I need someone to develop a custom single board computer system, which will take a network cable in, and if the ...device is connected to a single computer or device, display the IP address of the device. A .skp or .stl file of a case design with an LCD screen would be an ideal solution, along with a rechargeable battery and recharging circuit.

    $719 (Avg Bid)
    $719 Avg Bid
    5 bids

    I require the assembly various components in order to manufacture closed pneumatic circuit (see attached drawing). This product is currently being specified, therefore the final look is yet to be determined. I have labelled most of key items but more work is to be done once the specification is finalised. If you are able to produce this piece

    $764 (Avg Bid)
    $764 Avg Bid
    11 bids

    Looking for a circuit board designer / device programmer, You need to construct the device to have a small LCD screen and a rom chip that will have the application embedded - Once the data is sent from PC it will show on a LCD / LED display- The device will be connected with PC via USB for power - Data will be sent thru USB or via COM port. Ideally

    $1323 (Avg Bid)
    $1323 Avg Bid
    16 bids

    Need someone to verify a memory controller using UVM environment. CAN bus is used as a memory cycle initiator and write/read burst transactions need to be verified.

    $453 (Avg Bid)
    $453 Avg Bid
    3 bids

    Hi Hari, Hope you and your team are well. I've got a fairly simple design that i need to be modelled, if you are able to create a 3D model that would be perfect. I've attached a file you to look at so you have some idea of my requirements. The purpose of this system when it is finally built is to allow me to test and calibrate digital manometers

    $27 / hr (Avg Bid)
    $27 / hr Avg Bid
    1 bids
    Automatic Light Controller 6 days left
    VERIFIED

    It is a project to program an Automatic Light Controller . I will give the details later.

    $51 (Avg Bid)
    $51 Avg Bid
    1 bids

    A printed circuit board layout must be checked against the schematic to confirm that there are no short circuits or unrouted tracks. The files are provided in Protel format.

    $538 (Avg Bid)
    $538 Avg Bid
    25 bids

    The requirement is to check a printed circuit board layout against the schematic and make sure that there are no unrouted or short circuited tracks. The files are supplied in Protel format.

    $554 (Avg Bid)
    $554 Avg Bid
    13 bids

    To design and build prototype of full solid-state static voltage stabilizer using IGBT/ MOSFET in PWM AC Chopper/Inverter topology with Buck Boost Transformer with any suitable DSP IC # Deliverables WORKER MUST PROVIDE : 1. Complete and detailed Schematic Diagram of the product. 2. Complete artwork of the PCB including laser print out of the tracks

    $292 (Avg Bid)
    $292 Avg Bid
    1 bids

    I have a digital dimmer circuit that controls the voltage to a lighting load through phase cut technique as per the attached image. I am using a micro controller that receives the zero crossing signal and send the firing signal to the circuit to control phase cutting. The circuit is working fine in most conditions. It has only one drawbacks is that

    $53 (Avg Bid)
    $53 Avg Bid
    5 bids

    It's a basic home automation project. I am able to control the relay without any problem until i connect it with a ac appliance (bulb).

    $26 (Avg Bid)
    $26 Avg Bid
    13 bids

    I'm looking for someone to write a C program for a leave me alone box. The circuit consists of 2 transistors, a motor with built in limit switch, a double pole, double throw switch and a pull up or pull down resistor if needed. ideally you will know how to use pulse width modulation. I cant really justify spending over $80 a working box can be

    $104 (Avg Bid)
    $104 Avg Bid
    10 bids

    Create gerber files from circuit diagram or pcb transfer image

    $152 (Avg Bid)
    $152 Avg Bid
    7 bids

    Create Infogrpahics for my product Mega WordPress Controller. More details of the Product can be found in the below location. [url removed, login to view] [url removed, login to view]

    $401 (Avg Bid)
    $401 Avg Bid
    12 bids

    Crestron is the Audio and video controller, We are looking for the API Integration to control the Cisco SX80 Video conferencing solution from Crestron

    $51 (Avg Bid)
    $51 Avg Bid
    1 bids

    ...***PROJECT DETAILS*** I have created a detailed functional specification which I want you to help me transform into a circuit design. This is *not* a PCB layout project. This is a circuit design project. Although the circuit will likely use an ESP8266, I do not require that you have any experience with the ESP8266. Instead, I am looking for engineers

    $12 / hr (Avg Bid)
    $12 / hr Avg Bid
    11 bids

    The main objective of this project is to create an working LT spice simulation of Opto-Coupler circuit and to write a technical report with explanation of the design of the circuit.

    $29 (Avg Bid)
    $29 Avg Bid
    11 bids

    Looking for electronics engineers to design and develop circuit/pcb r&d. Also to be familiar with android / ios.

    $190 (Avg Bid)
    $190 Avg Bid
    24 bids

    Need someone to verify a memory controller using UVM environment. CAN bus is used as a memory cycle initiator and write/read burst transactions need to be verified.

    $146 (Avg Bid)
    $146 Avg Bid
    1 bids